![]() If the light is on, while some of the motors can be unlocked, it probably caused by the driver module, please replace the motherboard of base panel.If the light is green, please make sure that if the motor wire of big and small arm as well as base panel is loosened or not.if the status signal light is off, please reburn FPGA/MCU firmware.Check if the the plug of thermosensitive resistor is loosened or the resistor is short-circuited or disconnected.Ģ.3.1 start dobot magician, if you found there is any robotic arm unable to lock while the small arm can be unlocked, please confirm:.reset dobot magician and reconnect with Repetier host software.Please note: when you’re using 3d printing function, red light means there’s something wrong when read the temperature of heating head, please confirm: Cut off the power, take off the bottom case to replace the control panel to check if there’s something wrong with control panel.Cut off the power, take off the big arm and small arm’s cover, check the wire and socket if connect properly.Return firmware for FPGA/MCU to test if there’s something wrong with the software.Then control the dobot magician as usualġ ) check the module’s signal light, if it’s still dark, it may be caused by the module, please replace a new module Ģ) if the module’s signal light is on, please check if there is any other bluetooth devices disturbed (especially when you’re on the exhibitions.)ģ) if the module’s signal light is on, please check if the wifi and pc belong to the same router and if the login name and password are right.Ĥ) if the module’s signal light is on, please check if the joystick can open.ĥ) if all of above is failed, please replace a new module or new dobot magician to test.Īfter started Dobot Magician, if the signal light is red, please confirm:.Buzzing 3 times (2 times for wifi module, 4 times for joysticks), which means the initialization has completed.plug in the bluetooth/wifi/joysticks/ir detector/color detector module first.When stop dobot magician, only after the signal light turns to dark, the power is off. ![]() Otherwise it can damage dobot magician to some extent. Please make sure that the Dobot Magician has already cut off the power before connect or disconnect the external devices like bluetooth, wifi, joystick, IR detector, color detector and so on. Please download the leap.dll zip file from, unzip all files to DobotStudio root file category, relaunch DobotStudio. “Could not find leap.dll on your computer” Download URL:Īfter launched DobotStudio, here is the error: Please download BlocklyPatch zip file, unzip all files to DobotStudio root file category, relaunch DobotStudio. Some windows OS PC would have following error after clicked Blockly: If you can’t burn successful, an error pops up, which means there’s something wrong with the mainboard ports, you need to ask for maintenance. after completed the burning, wait for a while until you heard a buzzing, which means the burning is successful. Open Mcuisp->config->firmware->Dobot.hex, click to start Isp as follow:Ĭ. If all above solutions are failed, please close the DobotStudio, return the firmware with the Mcuisp software under tools file as follow screenshot:ī. Return the firmware by click Tools>DobotStudioĪ. Reboot your PC, only launch DobotStudio to connect Solution: please make sure that the USB has already connected with dobot magician and your PC and downloaded the driver successfully, if you don’t know how to install the drivers, please follow the structure on the manual in the package.Ģ) if you find the COM port in DobotStudio, but after clicking Connect button, the error are following:Ĭlose all possible applications which probably occupied the ports, relaunch the DobotStudio If you have any questions or suggestions about dobot magician, please email 1.1 Fail to Connect DobotStudioġ) click Connect to connect studio, if the error is “Please connect the Dobot first” Windows XP (this OS doesn’t support BLOCKLY and leapmotion)ģ. Here are the compatible OS for DobotStudio: Then Download the software and second-development related material on: Please purchase DOBOT MAGICIAN below first, 2.1 Bluetooth/Wifi/Joysticks TroubleshootingĢ.5 Save and Display Points Troubleshootingģ.2 Fail to connect Repetier Host, Fail to control XYZģ.4 Dobot Magician freezes after the 3D Printing startsġ.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |